Hired-hand Evolution Series 3000/3001: Wiring Kits for PVR-H User Manual download pdf

Wiring Kits for PVR-H to

EV-1200 or EV-3000/3001 Controllers

HIRED-HAND, INC. • 1733 County Road 68 • Bremen, AL 35033 USA • Phone 256-287-1000 • Fax 256-287-2000

Manual Part No. 4802-5108 rev 11-06 Page 1 of 4

Crimp Tool Small flat-head screwdriver

Wire Strippers

WARNING!

Only qualified electrician personnel familiar

with the construction and operation of this

equipment and the hazards involved should

install and/or service this equipment. Read

and understand all instructions and diagrams

before proceeding. Failure to observe this

precaution could result in equipment damage,

severe bodily injury, or loss of life.

DESCRIPTION

The two wiring kits described in this manual are for

wiring the PVR-H to EV-1200 Controllers or PVR-H to

EV-3000/3001 controllers. The kits provide a quick

and simple wire harness for connecting to the PVR-H

controllers. The kit includes the quick-connect wiring

harness and six female quick-connect crimp terminals

to connect to existing wire assemblies.

When the kit is received, check for shipping damage or

missing parts. Refer to Tables A and B for kit

content.

TABLE A: 6450-5108 PVR-H to EV1200

Wiring Kit Parts List

Part # Description Qty

1903-4042 HRNS PVR-H to EV1200 1

3006-0100 CONR Recpt ufstL.250 16-14 AWG 6

1.0 EV1200 Wire Harness

Installation

The EV1200 wire harness wires should be formed and

placed as shown in Figure 1 to allow access to the

switches and other terminal blocks.

(1) Disconnect all AC electrical power from the EV-

1200 and PVR-H controllers.

(2) Remove the 6-pin black terminal block (General

Purpose Analog Inputs) from PCB186 and remove

the two 3-pin green terminal blocks (PT Unit #1 &

PT Unit #2) from PCB188-3 as shown in Figure 1.

(3) Install the PVR-H Harness as shown. The wire

harness should be placed close to the circuit

board and toward the hinge to allow installation of

the metal electrical shield.

(4) Ensure that all wires are clear from the metal

electrical shield and from hole drilling locations.

(5) Refer to Section 1.1 for the wire connections

diagram from the EV1200 to the PVR-H.

WARNING!

Ensure that the Electrical Power Sources are OFF

during installation / wiring.

Figure 1: PVR-H Wiring Kit Installed inside

EV-1200 Controller

Quick

Connects

PVR-H to EV1200 Harness

General

Purpose

Analog Inputs

Connector

PCB188-3

Connectors

PCB186

1 2 3 4

Summary of Contents

Page 1 - Wiring Kits for PVR-H to

Wiring Kits for PVR-H to EV-1200 or EV-3000/3001 Controllers HIRED-HAND, INC. • 1733 County Road 68 • Bremen, AL 35033 USA • Phone 256-287-1000

Page 2

HIRED-HAND, INC. • 1733 County Road 68 • Bremen, AL 35033 USA • Phone 256-287-1000 • Fax 256-287-2000 Manual Part No. 4802-5108 rev 11-06

Page 3 - Installation

HIRED-HAND, INC. • 1733 County Road 68 • Bremen, AL 35033 USA • Phone 256-287-1000 • Fax 256-287-2000 Manual Part No. 4802-5108 rev 11-06

Page 4

HIRED-HAND, INC. • 1733 County Road 68 • Bremen, AL 35033 USA • Phone 256-287-1000 • Fax 256-287-2000 Manual Part No. 4802-5108 rev 11-06

Comments to this Manuals

No comments

Hired-hand Evolution Series 3000/3001: Wiring Kits for PVR-H User Manual

Browse online or download User Manual for Equipment Hired-hand Evolution Series 3000/3001: Wiring Kits for PVR-H. Hired-Hand Evolution Series 3000/3001: Wiring Kits for PVR-H User Manual [en]

Summary of Contents

Comments to this Manuals

Related products and manuals for Equipment Hired-hand Evolution Series 3000/3001: Wiring Kits for PVR-H